H&R Wheel Spacers BMW 525i 528i 530i 535i 545i 550i E60 / E61 (04-10) 3mm 5mm 10mm 12mm 15mm 20mm 25mm 30mm 45mm

Description

Fitment Information

• BMW 525i E60 (2004, 2005, 2006, 2007)
• BMW 525Xi Sedan E60 (2004, 2005, 2006, 2007, 2008, 2009, 2010)
• BMW 528i E60 (2008, 2009, 2010)
• BMW 530i E60 (2004, 2005, 2006, 2007)
• BMW 530Xi Sedan E60 (2004, 2005, 2006, 2007, 2008, 2009, 2010)
• BMW 530Xi Wagon E61 (2004, 2005, 2006, 2007, 2008, 2009, 2010)
• BMW 535i E60 (2008, 2009, 2010)
• BMW 545i E60 (2004, 2005, 2006)
• BMW 550i E60 (2006, 2007, 2008, 2009, 2010)

Specs & Features

• Bolt Pattern: 5/120
• Center Bore: 72.5
• Bolt or Stud: Bolt
• Thread Type: 12×1.5
• Sold as a pair
• Available in multiple styles

• DR Series
• DR Series spacers fit between the wheel and hub, and require longer wheel bolts (ordered separately.) Please verify bolt specifics before ordering (taper or round bolt head and shaft length.)

• DRA Series
• DRA Series spacers bolt to the hub with special wheel bolts (included) and provide new threaded holes for the existing wheel bolts.

Additional Note 2

DRM 20mm Wheel Spacers– If the depth of the wheel spacer is smaller than the length of the standard studs, the wheels used must allow for small cavities in the mounting pad of the wheel. If using wheels without cavities, the standard studs should be shortened so that they do not extend beyond the height of the spacer.

Additional Note 3

DRS 20mm Wheel Spacers– Careful attention must be paid to the vehicle hub height and inner wheel bevel measurements. Failure to follow the measurement guidelines below can result in serious damage to wheel spacers, wheels, and mounting hardware.

Additional Note 4

All DR-Systems require longer wheel bolts. These must be ordered separately. When ordering wheel bolts, please follow these guidelines:

a) If possible, name the brand of wheel.

b) New bolts must be longer than the original bolts by the width of the wheel spacer used.

c) The bolt head must be identical to the existing bolt: Taper 60 End digit 01 Round head for M12/d24 mm, for M14/d28 mm End digit 02 Round head for M12/d26 mm (e.g. OE VAG-wheels) End digit 03 Flat head for Porsche original wheels M14 x 1.5 End digit 06

d) Safety guidelines (Minimum number of turns for wheel bolts / nuts): M12 x 1.25 = 8.0 turns = approx. 10 mm of load bearing shaft length M12 x 1.50 = 6.5 turns = approx. 10 mm of load bearing shaft length M12 x 1.75 = 6.5 turns = approx. 12 mm of load bearing shaft length M14 x 1.25 = 9.0 turns = approx. 12mm of load bearing shaft length M14 x 1.50 = 7.5 turns = approx. 12 mm of load bearing shaft length 1/2″ UNF = 8.0 turns = approx. 11 mm of load bearing shaft length

e) Please ensure that the wheel bolts do not damage any part of the brake system (ABS sensors, etc..) Turn the wheel by hand and check clearance on the inside of the hub. The wheel should rotate freely. (Maximum tolerance for some vehicles is only 2mm- i.e., Rear Axle Mercedes.)